Parametric Effects on the Coefficient of Friction of a Novel Composite Material for Automobile Brake Linning
DOI:
https://doi.org/10.54392/irjmt2342Keywords:
Brake Lining, Temperature, Pressure, Coefficient of Friction, Composite MaterialAbstract
Brake lining, a friction lining material has over the years been produced mainly from asbestos. Asbestos health hazards have necessitated the need to source friction lining materials from other safer directions. A novel composite from local materials was developed. The brake lining production was a dispersion hardening process by the techniques of powder metallurgy of finely divided particles of the raw material powder mix. The raw materials included sawdust, resin, rubber latex, clay, carbon black, brass chips, zinc oxide and sulphur. The friction lining material thus produced, with its friction coefficient was analysed relative to its responses to increasing temperatures and pressures. The environment of increasing temperatures and pressures is its operating condition, in situ. Temperature range studied was from 300C-3000C, while pressure range was from 50KPa-250KPa. Results of the analysis showed the fiction coefficient not adversely affected, with minimum value at 0.31 and maximum value at 0.56.
References
O.A. Towoju, Braking Pattern Impact on Brake Fade in an Automobile, Journal of Engineering Science, 6 (2019) 11-16. https://doi.org/10.21272/jes.2019.6(2).e2
O.M. Chinedum, U.E. Richard, E.M. Chika, M.A. Chike, Production of low wear Friction Lining Material From Agro-Industrial waste, Springer Journal of Engineering and Applied Science, 74 (2022). https://doi.org/10.1186/s44147-022-00130-3
Y. Fikral, Optimum Design of Brake Friction Composites, Jurnal Tribologi, 30 (2021) 133-148.
E.O. Obidiegwu, H.E. Mgbemere, E.F. Ochulor, P.A. Ajayi, Characterisation of Train Brake Block Composite Reinforced with Aluminium Dross, Nigerian Journal of Technology, 39 (2020) 1123-1130. https://doi.org/10.4314/njt.v39i4.20
S.O. Ogbeide, P.D. Anwule, Modelling of Automobile Brake Pad wear, IRE Journal, 3 (2019) 227-239.
K. Naveen, B. Ajayi, H.S. Goyal, K.P. Kunvar, Evolution of Brake Friction Materials: A Review, Journal of Friction Wear, 47 (2021) 796-815.
K. Pradnya, P. Pradeep, K. Rajendra, Fade and Recovery Characteristic of Commercial Disk Brake Friction Materials: A Case Study, Taylor and Francis International Journal of Ambient Energy, 43 (2020) 2446-2452. https://doi.org/10.1080/01430750.2020.1730959
W.N. Avant, A.T. Samir, L.C. Arvind, Effect of Heat Conduction on Friction Pad Life in Disk Braking System, Interntional Journal of Applied Engineering Research, 13 (2018) 1-4.
S. Zhang, Q. Hao, Y. Liu, L. Jin, F. Ma, Z. Sha, D. Yang, Simulation Study on Friction and Wear Law of Brak Pad in High-power Disc Brake, Hindawi Journal of Mathematical Problems in Engineering, 20 (2019) 1-15. https://doi.org/10.1155/2019/6250694
S. Iiker, S. Banu, Effect of Braking Pressure on Friction and Wear Properties of Brake Linning, Journal of Current Research on Engineering Science and Technology, 7 (2021) 151-156.
A. Belhocine, M. Bouchetara, Temperature and Thermal Stresses of Vehicles Grey Cast Brake, Elsevier Journal of Research and Technology, 11 (2013) 671-682.
N. Keyan, H. Junjiao, H. Ming, Z. Nan, D. Jinhua, L. Zhaoyang, L. Zhe, L. Guimin, J. Zhen and J. Chengchang, The Influence of Braking Pressure on the Temperature and Stress Field of Iron-based Friction Pairs, Journal of Physics Conference Series, 1637 (2020) 1-7. https://doi.org/10.1088/1742-6596/1637/1/012038
B. Kumbhar, S. Patil, S. M. Sawant, Comparative Study of Automobile Brake Testing Standards, Springer Journal of the Institution of Engineers (India) Series C, (2017) 527-531. https://doi.org/10.1007/s40032-016-0289-y
S. Agarwal, D. Bharadi, S. Bhukan, V. Dewangan and S. Shenkar, Design of Dual Brake Caliper System, International Research Journal of Engineering and Technology, 8 (2021) 3067-3073.
S.S. Dharamkar, G.D. Shelake, I.M. Quraishi, Analaysis of Vented Disk by Using Software, Journal of Engineering Technology and Innovative Research, 5 (2018) 705-715.
A.P. Irawan, D.F. Fitriyana, C. Tezara, J.P. Siregar, D. Laksmidewi, G.D. Baskara, M. Z. Abdullah, R. Junid, A.E. Hadi, M.Z. Hamdan, N. Najid, Overview of the Important Factors Influcing the PerformanceEco-friendly Brake Pads, Journal of Polymers (Basel), 14 (2022) 1180. https://doi.org/10.3390/polym14061180
F. Talati, S. Jalalifar, Investigation of Heat Transfer Phenomena in a Ventilated Disk Brake Rotor with Straight Radial Rounded Vanes, Journal of Applied Sciences, 8 (2008) 3583-3592. https://doi.org/10.3923/jas.2008.3583.3592
L. Nam-Jin, K. Chul-Gao, Effects of Variables Disk Pad Friction Coefficient for the Mechanical Brake System of a Railway Vehicle, Journal of PLOS/ONE, 10 (2015) 1-18. https://doi.org/10.1371/journal.pone.0135459
M.O. Petinrin, A.A. Oyadele, O.O. Ajide, Numerical Analysis of Thermo-elastic Contact Problem of Disk Brakes for Vehicle on Gradient Surfaces, World Journal of Engineering and Technology, 4 (2016) 51-58. http://dx.doi.org/10.4236/wjet.2016.41006
A. Bulsara, D. Lakhani, Y. Agarwal, Y. Agiwal, Design and Testing of an Adjustable Brake System for an FSAE Vehicle, International Journal of Research in Engineering and Technology, 6 (2017) 25-29. https://doi.org/10.15623/ijret.2017.0610005
A. D. Secrist, R. W. Hornbeck, An Analysis of Heat Transfer and Fade in Disk Brakes, ASME Journal of Manufacturing Service and Engineering, 982 (1976) 385-390. https://doi.org/10.1115/1.3438884
M.S. Palwade, K.W. Kolekar, Review of Friction Material Effects on Performance of Disk Brake, International Journal for Research in Applied Science and Engineering Technology, 6 (2018).
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Benedict U. Iyida, Azubuike M. Nwankwo, Thomas O. Onah (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
How to Cite
